![]() Wait a minute, then type "pi", hit Enter, then "raspberry", and hit enter.Įnable SSH with: sudo /etc/init.d/ssh start.Note the default keyboard layout will be the standard QWERTY US layout, so mind your "Y"s and "Z"s, and your "-"s and "/"s. Plug in the keyboard and boot the RPi.But if it's not and you're stuck, read on:Įnabling it is very simple, a lot simpler than most of the answers I've seen here, if you have a USB keyboard: Apparently SSH is enabled by default now. Once upon a time, SSH was definitely not enabled on my Raspbian images. SSH is not enabled by default in Debian Wheezy (Raspbian). The easy way (if you have just a keyboard) You should know what IP it roughly has (to a /24) so scanning is simple: sudo nmap -sV -open 192.168.0.0/24 -p22 Use nmap on another computer to scan for it. Plug a monitor in and run ifconfig (cheating!) Netgear is especially good at showing "Attached Devices". If you're struggling to find it on your network. Run: for i in 2 3 4 5 do sudo ln -s /etc/init.d/ssh etc/rc$i.d/S02ssh done What I'm suggesting will not work from Windows without Cygwin (or other). At least something using bash, or something compatible. I'm assuming you're doing this from a Linux computer. Confused? Never mind - doing the damage is simple. script at various points in the /etc/rc.d/. All this really does is create a symlink to the /etc/init.d/. If you're not, you're left in the position where you have to somehow externally run update-rc.d. You boot, a nice graphical menu gives you some options (including whether SSHD should load at boot) and then dumps you out on a command line. And again, specify the root device, not a partition (/dev/sdj, not /dev/sdj1) - what you type must not end with a number.None of the boot_enable_ssh.rc stuff exists in current Raspian builds. Run the above command and then plug in the device. ![]() An easy way to find out what device designation your device is getting: $ watch lsblk I mean, assuming the storage devices really are identical. The described method will work, and if it doesn't there are exactly two possibilities - a wrong entry, or one of the storage devices has become corrupted. $ sudo dd if=image.img of=/dev/(device designation) bs=32M Do not allow your system to mount the device - read the note above about avoiding mounting.Ĭreate a clone of the original device using the image file you created above: Remove the source device, insert the destination device. dev/sdj not /dev/sdj1, as an example (your device designation will differ). IMPORTANT: DO NOT specify a partition, specify the root device, i.e. $ sudo dd if=/dev/(device designation) of=image.img bs=32M Ĭreate an image of that device, like this: If you only have one read/write connection, do it this way:Ĭonnect the source device and don't let your system mount it - and if you find that you have to unmount the device, it will lose its device designation - it must not be allowed to mount in the first place.įind out what the device's designation is (see note 1 at the bottom of this post). The point is to find out what you did wrong and fix the problem. Therefore either the target device is corrupted/faulty or you're doing something wrong. You report that you cannot make a clone with two identical storage devices at hand. ![]() The best thing? The base model is only $20 $5!.ĭo you know a related subreddit? We'd love to know.Īctually, you have never shown us exactly what you typed. Welcome to /r/raspberry_pi, a subreddit for discussing the raspberry pi credit card sized, ARM powered computer, and the glorious things we can do with it. Pi project ideas: There's a huge list right here on this sub! Friendly reminder: Please don't just post pictures of unused pis - do a project!Ĭomplete r/raspberry_pi Rules Check the FAQ and Helpdesk here ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |